AN EASY INSTRUCTION FOR INSTALLING A BATHTUB

An Easy Instruction for Installing a Bathtub

An Easy Instruction for Installing a Bathtub

Blog Article

Call Today

Just how do you feel in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a new one is likewise a reasonably challenging job. If the old tub is readily accessible, the job can relocate immediately; if you have to open a wall to eliminate the old bathtub and also place the brand-new bathtub, the job is much harder. In either situation, the project is within a house handyman's skills, although you will certainly require an assistant to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and are comfortable trying it. Rather than hiring a contractor to take over a halfway-completed project, it is far better to consider using one prior to you begin. Chances are you may need a professional plumber to make tube links.
This article will assist you install a new bath tub in your shower room if you have currently gotten a brand-new tub and also do not require to transform the setup of your previous water supply pipes.
Your tools as well as material list need to comprise the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Planning for the Installation


    Firstly, the supporting structure supplied with the bath should be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to prevent strain on the bathtub.
    Fit the flexible tap ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
    Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its final placement.

    Removing Old Taps


    If you require to change old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the water. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of eliminating the existing taps can be rather troublesome due to the limited gain access to that is commonly the instance.
    Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, use the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
    Prior to moving on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

    Mounting the Bath tub


    Utilizing the two wood boards under its feet, position the bath tub in the needed setting. The wood boards are valuable in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little factors.
    The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the tub till the level reviews degree.
    To mount taps, fit all-time low of the outermost flexible faucet adapter to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
    Activate the water system and examine all joints and new pipework for leakages and tighten them if essential. Load the tub and likewise examine the overflow outlet and the regular outlet for leakages.
    Finally, fix the bath paneling as defined in the producer's instruction manual. Tiling as well as sealing around the tub should wait till the bathtub has actually been utilized a minimum of when as this will certainly settle it into its final position.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next, position the tap in the installing hole in the bath/basin ensuring that the washers are in location in between the faucet as well as the sink. Safeguard the tap in place with the manufacturer supplied backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind should be linked to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Tub


    In the area where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall surface between the bath and the tiling, resulting in issues with dampness and also possible leaks to the ceiling listed below.
    You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly early if you do not consider this activity prior to sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof sticky as well as grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub

    As a keen reader on How to Install a Bathtub Yourself, I imagined sharing that information was a smart idea. Please take a moment to promote this blog posting if you appreciated it. I cherish reading our article about How to Install a Bathtub Yourself.


    Call, we deliver!

    Report this page